DraftCore, home Your first plan, on us Book a demo

Your first plan, on us

Got a plan on your desk right now you'd rather not draft by hand?

Send it to us, or run it on your last job. In the first ten minutes you watch the architect's file turn into the plan, the panel and the sheets. The other twenty are for your questions. You keep the files. No card.

One plan per firm. One floor, one unit type.

The review list, redrawn for this page from the app. Every call it made, why, and what it points at.

The whole first pass. Yours to keep.

What you get from the first plan
Your architect's file, cleanedThe floor plan (A1) and the ceiling plan (C1). The original is never touched.
The first-pass electrical planLights, controls, receptacles, equipment, circuits and home runs, the panel schedule with its loads, the riser, the sheets with your title block.
The review listEvery assumption it made, with why, and the code section where one applies.
Thirty minutes with the person who built itOn a call, watching it run on your file. Ask anything. That is the demo.
The filesDWG and DXF. Open them in whatever you draft in.
The revision tooWhen the architect reissues that plan, we run the revision on it too, free, and show you what moved and which devices it hit.

One file. Thirty minutes.

YouUs
Send one DWG or DXF, or a CAD-exported PDF with its layers. One floor, one unit type.Clean it. Run DraftCore Electrical on it. Walk you through the list.
Thirty minutes on a call.Answer every "why did it do that".
Nothing else. No card. Nothing renews.Send you the files the same day.

Measured on a 6,900 square foot warehouse and office building: under two minutes start to finish, about 15 seconds of it machine time. Our own machine, October and November 2026. One building.

Or run it on your last job and compare it to what you drew. That is the fairest test we know, and it is the one we run on ourselves.

What we promise, and what we do not.

We do not promise the plan is right.

Your engineer does. DraftCore drafts the first pass; your engineer reviews everything it drew. The stamp is theirs.

We do promise you see every assumption it made.

Each one is a card on the review list, with its reason. Nothing is decided silently.

Your files the same day.

If they are not, your next plan is on us too.

No card. Nothing renews on its own.

When the architect reissues that plan, we run the revision on it too. Free. Run it on your last job and compare it to what you drew.

The thirty minutes, in order.

Times from a 6,900 square foot warehouse and office building, our own machine, 2 November 2026. A bigger plan takes longer to read, not much longer to run.

  1. Minutes 0 to 2

    Your file opens

    The architect's DWG as it came, every layer and every consultant's mess. We press Clean. The A1, then the C1.

  2. Minutes 2 to 4

    Generate E plan

    Eleven steps. Lights, the E, controls, power, comm, circuits, panels, riser, sheets. On a 6,900 square foot building, about six seconds.

  3. Minutes 4 to 12

    The review list

    We read the cards with you. Click a symbol: why it is there. The panel, the riser, the sheets.

  4. Minutes 12 to 30

    Your questions

    Your standard, your symbols, your revisions, what it does not do. Then you decide if it is worth going further.

Read this before you send a file.

A firm that sends a scanned as-built and gets nothing back concludes the product is broken. This is here so that does not happen to you.

DWG and DXF, in and out

DraftCore reads both and writes both. It has its own CAD engine, so it fits the workflow you already have rather than replacing it.

CAD-exported PDFs, going in

A PDF works as an input only if it came out of CAD and still carries its layer information. Scanned, photographed or flattened PDFs will not work, and DraftCore does not return PDFs.

One plan for the first run

One floor, one unit type. Multi-unit buildings are handled one unit at a time. Stacked floors on one sheet can be split, but send one plan for the first run and we will show you the rest on the call.

More time to be an engineer. Your seal stays yours.

DraftCore drafts the first pass, your engineer reviews everything it drew. The stamp is theirs.

It is not replacing anyone. It is not the final word and it is not a compliance engine.

What it needs from you

  • A DWG, DXF or layered CAD PDF
  • One floor, one unit type
  • Permission to open the file

What it will not do

  • Decide for your engineer
  • Seal, or check for code compliance
  • Change the architect's original
  • Run on a scanned PDF

Book the call. Send the file after, or on the call.

Chase KnoxBook a meeting with Chase for 30 minutes.

A form should never be the only way to reach a person. You can email us directly at chase@draftcore.ai. A person reads every message.

Your first plan, on us. Run it on your last job.

  1. Your architect's file, cleaned: the floor plan (A1) and the ceiling plan (C1). The original is never touched.
  2. The first-pass electrical plan: lights, controls, power, circuits and home runs, the panel schedule with its loads, the riser, the sheets.
  3. The review list: every assumption it made, with why.
  4. A 30-minute meeting with Chase, watching it run on your file.
  5. The files, DWG and DXF. Yours to keep.
  6. When the architect reissues that plan, we run the revision on it too. Free.

No card. Nothing renews on its own. Run it on your last job and compare it to what you drew.

If it is useful, we set your firm up. You keep the files either way.

Thank you. We will be in touch to pick a time.

A person from DraftCore reads it and replies from chase@draftcore.ai.

Sending the drawing

Reply to our email with one DWG or DXF, or a CAD-exported PDF with its layers. Or bring it to the call.

You confirm you may share this drawing with us for this run.

Step 1 of 2

Fields marked * are needed.

Step 2 of 2, optional. Skip any of it.

No card. Nothing renews. We reply from chase@draftcore.ai. Privacy.

Before you send a file.

Is it really free?

The first plan is. One per firm. If you want to keep going after it, we talk about setting your firm up. Nothing renews on its own.

What if the plan is not good?

Then you have lost thirty minutes and we have learned something. You keep the files either way.

Who sees my drawing?

If you want to know where the file goes before you send it, ask, and we answer in writing.

Can I run it myself instead?

Clean, yes, in the web app today. During early access we set up the electrical module with each firm ourselves.

What does it run on?

For your first plan, nothing on your side: we run it on a call while you watch and send you the DWG and DXF. DraftCore itself is available for Mac. Runs on Apple Silicon Macs (macOS 14 or later). A cloud version is coming soon.

Does it need AutoCAD?

No. It has its own CAD engine and reads and writes DWG and DXF.

Which codes?

NEC 2023, and North Carolina's 2020 amendments, cited by section on the item. Other editions as firms need them.

What kind of work?

Commercial, residential, tenant fit-out, multi-family and renovation work. Scored so far on commercial, tenant fit-out and renovation jobs.