DraftCore, home Your first plan, on us Book a demo

DraftCore Electrical

Open the file. Press Clean. Press Generate. Then review.

DraftCore is one product: a CAD workspace with a Clean step and an electrical module, DraftCore Electrical. The architect's file goes in. The electrical plan comes out on its sheet, for your engineer to review.

An invented office drawn by DraftCore Electrical: lights on the ceiling grid, a switch past the latch jamb, an occupancy sensor, receptacles on the walls, and a home run to the panel. S OS PP-1 5 OFFICE past the latch jamb, a firm rule
Invented geometry, drawn for this page. Not a client drawing.

What each press draws.

Every step runs on the architect's DWG as it came. This is the order the buttons sit in. Generate E plan runs them all, and the menu beside it runs any one alone.

On a 6,900 square foot warehouse and office building, the eleven steps took about six seconds of machine time on our own machine, 2 November 2026. The whole job, start to finish with a person pressing the buttons, was under two minutes.

  1. Clean

    The floor plan

    Send the architect's DWG as it came. Clean reads what the plan is and makes the A1: the clutter goes, the walls, doors and room names stay, with the references lined up. Clean writes a new file. Your original stays as it came.

  2. Clean again

    The ceiling plan

    Press Clean again for the C1. If the architect never sent a ceiling plan, DraftCore draws the grid from the rooms.

  3. Generate E plan

    One press, eleven steps

    Lighting, Make E, Controls, Power, Comm, Circuits, Controls again, Circuits again, Panel Schedules, Riser and Sheets. Undo takes back a whole step.

  4. Lighting

    Fixtures on the grid

    Fixtures land by room type and ceiling, with the emergency and exit lights where they have to go.

  5. Controls

    Switches and sensors

    Switches go past the latch jamb. Sensors go where the energy code asks for them.

  6. Power and Comm

    Receptacles, equipment, comm

    Receptacles follow what the room is. Equipment and comm outlets go in the same pass.

  7. Circuits

    Circuits and home runs

    Circuits go to the panel, and the home runs are drawn and tagged. If nobody drew a panel, it proposes one and flags it for your call.

  8. Panel Schedules and Riser

    Panel schedules and the riser

    Every circuit, breaker and load is read off the placed devices, not typed. The riser runs source to panel.

  9. Sheets

    The sheets, then the review list

    The sheets come out with the title block, legend and notes, at scale. Then the review list: every call it made, why, and what it points at.

Every symbol carries its values.

The panel schedule, the loads and the riser are read off the placed devices, not typed. Draw a home run by hand and the panel follows it. Undo puts it back.

So the plan, the panel and the riser agree, because they are one record.

Every symbol says why it is there.

Click one: "Made by DraftCore Electrical, Controls. Reason: sensor switch." Every assumption it made is a card on the review list, with its reason and the thing it points at. Nothing is decided silently.

Where a code rule applies, the item names the section and the edition, including the state amendment. NEC 2023, and North Carolina's 2020, so far. It never reproduces code text.

Your symbols, your layers, your rules.

Your symbols, your layers

Your firm's standard is captured when we set your firm up. From then on DraftCore Electrical draws in your standard, with the firm's own blocks and layer names, from the firm's symbol library.

Your standards, on screen

Your standards sit in Settings with their sources. Keep one firm standard, add one per client or building type, and pick one per job.

The same every time

Same drawing in, same drawing out, every time. Your standard applied the same way on every job, by rules you can read.

Renovation scope

Mark the rooms the job leaves alone. The stages skip them.

Stacked floors

The architect put four floors on one sheet. One press makes four plans, one per floor. In the desktop app.

One area of a big plan

Draw the area you want cleaned. It keeps whole rooms and drops the rest.

Nothing lands because a model said so.

The rules came from doing this work. They govern every AI step. Each AI step is one switch in the firm's settings, off by default for the module; what it proposes goes through the rules and onto the review list.

The fixture schedule from a picture. With the AI assist on, point it at the schedule image or scanned PDF. It reads the rows into the import table with each cell's crop beside it. You check every row.

No AutoCAD seat needed to produce the sheets.

DraftCore is its own CAD workspace with its own engine; the sheets come out as DWG and DXF. Several drawings open, sheets and viewports, plotting. View, edit, draw.

DWG and DXF, in and out. And a PDF only if it came out of CAD with its layers. A scan will not work.

It never seals.

DraftCore drafts the first pass, your engineer reviews everything it drew. The stamp is theirs.

The work it is built for: commercial, residential, tenant fit-out, multi-family and renovation work. Scored so far on commercial, tenant fit-out and renovation jobs. During early access we set up the electrical module with each firm ourselves. Clean also runs in the web app.

DraftCore does

  • Cleans the architect's file to the A1 and C1
  • Drafts lights, controls, power, circuits
  • Builds the panel schedule, the riser, the sheets
  • Lists every call it made, with why

Your engineer does

  • Reads the list and the plan
  • Moves, keeps or rejects each item
  • Decides what the drawing says
  • Stamps it, and answers for it

Your first plan, on us. Run it on your last job.

Thirty minutes, your file, the whole first pass, yours to keep.

SIFDR, Smart Intelligent Fast Drawing Recognition, is the name of the Clean step. It cleans to the floor plan and the ceiling plan.